得到警告“赋值从指针进行整数转换而不进行强制转换”

Question

我在第59行收到此警告：

赋值从指针转换为整数而不进行强制转换。

我该如何解决？这是整个文件（从http://pastebin.com/BrmjBAS0复制）：

/* bkerndev - Bran's Kernel Development Tutorial
*  By:   Brandon F. ([email protected])
*  Desc: Global Descriptor Table management
*
*  Notes: No warranty expressed or implied. Use at own risk. */


/* Defines a GDT entry */
struct gdt_entry
{
    unsigned short limit_low;
    unsigned short base_low;
    unsigned char base_middle;
    unsigned char access;
    unsigned char granularity;
    unsigned char base_high;
} __attribute__((packed));

struct gdt_ptr
{
    unsigned short limit;
    unsigned int base;
} __attribute__((packed));

/* Our GDT, with 3 entries, and finally our special GDT pointer */
struct gdt_entry gdt[3];
struct gdt_ptr gp;

/* This is in start.asm. We use this to properly reload
*  the new segment registers */
extern void _gdt_flush();

/* Setup a descriptor in the Global Descriptor Table */
void gdt_set_gate(int num, unsigned long base, unsigned long limit, unsigned char access, unsigned char gran)
{
    /* Setup the descriptor base address */
    gdt[num].base_low = (base & 0xFFFF);
    gdt[num].base_middle = (base >> 16) & 0xFF;
    gdt[num].base_high = (base >> 24) & 0xFF;

    /* Setup the descriptor limits */
    gdt[num].limit_low = (limit & 0xFFFF);
    gdt[num].granularity = ((limit >> 16) & 0x0F);

    /* Finally, set up the granularity and access flags */
    gdt[num].granularity |= (gran & 0xF0);
    gdt[num].access = access;
}

/* Should be called by main. This will setup the special GDT
*  pointer, set up the first 3 entries in our GDT, and then
*  finally call gdt_flush() in our assembler file in order
*  to tell the processor where the new GDT is and update the
*  new segment registers */
void gdt_install()
{
    /* Setup the GDT pointer and limit */
    gp.limit = (sizeof(struct gdt_entry) * 3) - 1;
    gp.base = &gdt;

    /* Our NULL descriptor */
    gdt_set_gate(0, 0, 0, 0, 0);

    /* The second entry is our Code Segment. The base address
    *  is 0, the limit is 4GBytes, it uses 4KByte granularity,
    *  uses 32-bit opcodes, and is a Code Segment descriptor.
    *  Please check the table above in the tutorial in order
    *  to see exactly what each value means */
    gdt_set_gate(1, 0, 0xFFFFFFFF, 0x9A, 0xCF);

    /* The third entry is our Data Segment. It's EXACTLY the
    *  same as our code segment, but the descriptor type in
    *  this entry's access byte says it's a Data Segment */
    gdt_set_gate(2, 0, 0xFFFFFFFF, 0x92, 0xCF);

    /* Flush out the old GDT and install the new changes! */
    _gdt_flush();
}

Answer 1

好，让我将此放在上下文中...

struct gdt_ptr
{
    unsigned short limit;
    unsigned int base;
} __attribute__((packed));

struct gdt_entry gdt[3];
struct gdt_ptr gp;

gp.base = &gdt;

您are将指针（&gdt）分配给整数（gp.base）-因此出现错误：-）

我怀疑您实际上想要（或类似的东西）：

struct gdt_ptr
{
    unsigned short limit;
    struct gdt_entry *base;
} __attribute__((packed));

或者，因为以后您将地址作为它的组成部分来评估，所以请保持定义不变，然后进行分配

Answer 2

我听说地址应该保留在size_t中，但是我真的想保留地址在int中，也许只是将其投射？ gp.base = (int) &gdt;

Answer 3

我之前遇到过这个问题，类型转换工作：

gp.base = (unsigned int)&gdt

Answer 4

gp.base = (unsigned int)&gdt