XMEGA-A3BU Xplained-确定是否通过使用DMA轮询来按下按钮1

Question

如果通过使用轮询按下SW1，则分配需要我们打开LED指示灯。我相信我正在设置每个端口的方向并正确读取寄存器。但是，当我按SW1时没有任何反应。代码运行时无法调试和断点代码以查看寄存器中的内容。

[[HWGuide]状态：[HWGuide]：http://ww1.microchip.com/downloads/en/DeviceDoc/doc8394.pdf

//LED0 = PR0 (PORTR PIN 0)
//LED1 = PR1 (PORTR PIN 1)
//SW1  = PF1 (PORTF PIN 1)

[[数据表]状态：[数据表]：http://ww1.microchip.com/downloads/en/DeviceDoc/atmel-8362-8-and-16bit-avr-microcontroller-atxmega256a3bu_datasheet.pdf

//PORTR starts at address = 0x07E0
//PORTF starts at address = 0x06A0

[手动]状态：[手动]：http://ww1.microchip.com/downloads/en/DeviceDoc/Atmel-8331-8-and-16-bit-AVR-Microcontroller-XMEGA-AU_Manual.pdf

//Data Input Value register on I/O = (Addr) + 0x08 = 0x06A8 (PORTF)

代码：

#define PORTR    *((volatile unsigned char *)0x7E0) /* I/O Port Register */
#define PORTF    *((volatile unsigned char *)0x6A0) /* I/O Port Register */
#define PORTF_IN *((volatile unsigned char *)0x6A8) //PORTF Input Value Reg
#define PORTR_OUTTGL    *((volatile unsigned char *)0x7E7) //LED Toggle Reg

#define ReadReg(port)           (port)
#define WriteReg(port, value)   (port = value)

int main(void)
{
    //set PORTR direction
    WriteReg(PORTR, 0xFF);
    //set PORTF direction
    WriteReg(PORTF, 0x00);
    while(1)
    {
        if((ReadReg(PORTF_IN) == 0xFD)) //if PF1 = 0
        { 
            WriteReg(PORTR_OUTTGL, 0x3); //toggle LEDs
        {
    {
}

我希望寄存器读取（0x02）0000 0010或取反（0xFD）1111 1101，如果按下按钮，则LED点亮或熄灭。

Answer 1

使用位操作来隔离我尝试轮询的位。不知道可以将其他位设置为什么。

int main(void)
{
    //set PORTR direction
    WriteReg(PORTR, 0xFF);
    //set PORTF direction
    WriteReg(PORTF, 0xF9);
    while(1)
    {
        char statusPF1 = (ReadReg(PORTF_IN) & 0x02) >> 1;
        char statusPF2 = (ReadReg(PORTF_IN) & 0x04) >> 2;

        if((statusPF1 == 0)) //if PF1 = 0
        {
            WriteReg(PORTR_OUTTGL, 0x01); //toggle LED0
            _delay_ms(1000);
        }
        if((statusPF2 == 0)) //if PF2 = 0
        {
            WriteReg(PORTR_OUTTGL, 0x02); //toggle LED1
            _delay_ms(1000);
        }
        if ((statusPF1 != 0) && (statusPF2 != 0))
        {
            _blinkLEDs();
        }
    }
}